Top 8 Betaflight Flight Controller – Hobby RC Quadcopters & Multirotors

As an Amazon Associate I earn from qualifying purchases.

1. Matek


Matek F405-STD BetaFlight STM32F405 Flight Controller Built-in OSD Inverter for RC Multirotor FPV Racing Drone

Matek #ad - 6x pwm / dshot outputs without conflict / 2x 2812LED outputs option / 5x UARTs.1x 16pin bottom mounted ffc slot for fchub-6S, FCHUB-VTX or FCHUB-W connection. 3x leds for fc status blue, red and 3. 3v indicatorRed. 4x pairs of corner pads for ESC Signal/GND connections DSHOT compatible. 2x 2812led outputs option / 5x uarts / 1x pair i2C1 pads 1x Side-press button for BOOTDFU mode.
BrandMatek #ad
ManufacturerMatek #ad
Part NumberF405-STD



BETAFPV F4 1S Brushed Flight Controller with SPI Frsky Receiver OSD Smart Audio for FPV Tiny Whoop Micro Racing Drone

BETAFPV #ad - For some basic guidance and typical FAQ, please visit our official website or feel free to contact us. Designed to work with current Tiny Whoop or Blade Inductrix setups. Betaflight osd on screen display is integrated in betafpv f4 brushed flight controllers that shows important flight data on your FPV feed, rates, such as battery voltage, current draw and much more.

Any technical issue or support is needed please feel free to contact me. The world's first compatible betaflight osD, FrSky Rx, BetaFlight firmware, born for acro flight controller for the Micro Whoop or Blade Inductrix quadcopter. Built-in spi frsky d16 protocol native receiver, compatible with almost ALL Frsky radiose.

G. The flight controller board comes pre-flashed with betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2. 0 connector, AKA PowerWhoop connector. Taranis x9d/x9d plus/X7 or Frsky compatible transmitter module. You can even use it as a menu to change your quad’s PID, filters and other settings.
BrandBETAFPV #ad
ManufacturerBETAFPV #ad
Height0.79 Inches
Length1.97 Inches
Weight0.02 Pounds
Width1.97 Inches
Part Number00313249



HAPPYMODEL Crazybee F4 PRO V3.1 AIO Flight Controller Built-in 12A ESC Betaflight OSD Compatible for Frsky RX FPV Racing Drone

HAPPYMODEL #ad - Warm tips: this produt not including VTX and Camera. For onboard frsky spi d8 receiver version: compatible with FrskyD FrskyX Frsky_X_LBT SFHSS REDPINE protocol. This flight controller is already pre-solder buzzer, external receiver wires, 5pin vtx wiresjust plug to Happymodel Whoop_vtx or Whoop_vtx_hp or Diamond VTX and also the xt30 power wires. Onboard 4in1 esc: support for blheliSuite programmable, 12A continuous peak 15A 5 seconds. Flight controller: built-in 5aeach blheli_s 4in1 esc dshot600 ready, Built-in Betaflight OSDSPI Control, For 2-4S battery input DC 7V-17V.
ManufacturerHappymodel #ad
Part NumberZ42883

4. QWinOut


QWinOut Newest PIKO BLX Betaflight Micro Flight Controller for DIY Indoor Mini Micro FPV Quadcopter Racing Drone F3 CleanFlight

QWinOut #ad - Piko blx micro flight controller FC for FPV Quad Race F3 CleanFlight. Designed nothing short of revolutionary, the PIKO BLX Micro Flight Controller changes everything - the true ultimate in the insanity fueled micro FPV racing scene.

Ultra light, astonishingly small and packed with massive levels of performance capability, the PIKO BLX is the one and only flight controller that is ready & waiting to devastate the micro FPV competition. Unlike any other system available today, the piKO BLX provides an all in one solution that brings forth the ultimate in simplified sophistication, utilizing industry leading technology that has never been seen in a system this compact.
BrandQWinOut #ad
ManufacturerQWinOut #ad
Part NumberM22943

5. Accrie


Accrie Toys and Games Holybro Kakute F4 V2 STM32F405 Flight Controller with Betaflight OSD for RC Multirotor FPV Racing Drone

Accrie #ad - The holybro kakute f4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster f4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization! Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same time. The kakute f4 is designed to support all serial protocols at once.
BrandAccrie #ad
ManufacturerAccrie #ad
Part NumberAccrie



Blackbox,Configuration and Firmware Flash via APP 45A BLHeli 32 4-in-1 ESC for FPV Drone DJI Air Unit, SpeedyBee F7 Flight Controller Stack 30x30,BF/EMU Supported,Wi-Fi&Bluetooth

SPEEDY BEE #ad - Even can configure motor direction wirelessly. Support blheli 32 ESCs. Support 45a continuous output and 55A burst output10s, ready for your strongest 6S motors. Easily connect to dji air unit: v2 f7 fpv fc included a connector specifically for DJI air unit, so installation should be a breeze.

Usb type-c and 22mm cutouts for FPV camera on FC and ESC boards compact more fpv frames. Just need to connect speedyBee App, it supports Betaflight/EMU/INAV full configuration. Bf/emu full support: whether you're at home or the field, your speedyBee F7 V2 is ready for you all the time. First flagship 4-in-1 esc: built with the finest components, speedybee's latest flagship ESC features a pure and high performance.

World's first fc stack with wireless firmware flasher and blackbox analyzer: To simplify FPV, SPEEDY BEE creates the world's first FC stack that can flash the firmware and analyze the blackbox wirelessly anywhere just need a phone. No more need a laptop: configure your fpv drone, or fine-tune your PIDs, access your blackbox data, and configure any other parameters in just a few minutes.
ManufacturerSPEEDY BEE #ad
Height0.31 Inches
Length1.65 Inches
Weight0.05 Pounds
Width1.5 Inches
Part NumberSPEEDY BEE V2



BETAFPV F722 35A 2-6S AIO Brushless Toothpick Flight Controller BLHELI_S 35A ESC No RX with XT60U Connector for 4-5inch Toothpick Drone 2-6S FPV Brushless Motor

BETAFPV #ad - It is perfectly suitable for 4-5inch toothpick drone. Increased the optionality of external devices. Support dji digital vtxcome with a 6-pin pluggable connector cable, specially designed for DJI digital VTX system, which is convenient for installation.

F722 aio 35a toothpick fcbetafpv newest 35a aio toothpick brushless flight controller comes with F722 chips and BLHELI_S ESC firmware. Performanceit can handle 35a continuous current40A burst, totally supports the 2-6S lipo battery, brings the drone a stronger flight performance. Pilots can use for VTX, external receiver, GPS etc.

It can provide you a better performance capability and higher calculation speed, which brings pilots a more stable and smoother flight. 6 full uarts6 full uarts are available on this f722 aio 35a board. Compatible drone&motorsf722 aio 35a fc supports 2-6s batteries, compatible with 14xx 15xx 16xx 18xx 20xx FPV brushless motors.
BrandBETAFPV #ad
ManufacturerBETAFPV #ad
Part Number00313830

8. iFlight


IFlight SucceX-D F7 TwinG Dual ICM20689 Flight Controller F7 FC Built-in OSD BEC Current Sensor Black Box for DJI FPV Air Unit HD Version…

iFlight #ad - F7 fc included a connector specifically for DJI air unit, so installation should be a breeze. Fc board add the popular and reliable USB Type-C instead of Micro USB which makes connection easily.

Built-in osd, double 5v/2. 5a, 9v/2. 5a bec, high-performance hardware, optimized circuit design, further guarantees powerful performance of flight controller. This flight controller is ready for anything with 5 uarts, 8 motor outputs, Dual ICM20689 gyro, 32mb blackbox and a powerful F7 processor to run it all. The f7 flight controller hd version is designed to work seamlessly for DJI’s new HD FPV system.
BrandiFlight #ad
ManufactureriFlight #ad
Weight0.06 Pounds
Part NumberSucceX-D